Переходник пылесоса PRO
Переходник шланг ↔ инструмент: обычные, плоские и магнитные соединения, конусность, зазоры, стопор, магниты и центрирующее кольцо.
Configure the model
Review the parameters, then open the model in the builder. Change dimensions methodically and inspect the result before manufacturing.
Open in builderOutput and formats
The builder displays a 3D preview. Available export formats, design saving and ordering depend on the model and account permissions and are shown in the interface.
Parameters
| Parameter | Units | Range |
|---|---|---|
| Dimension by X - width | Shown in the builder | — – — |
| Dimension by Y - depth | Shown in the builder | — – — |
| Dimension by Z - height | Shown in the builder | — – — |
| Type первого конца | Shown in the builder | — – — |
| Номинальный diameter первого соединения | Shown in the builder | 10.0 – 250.0 |
| Как соединение садится на hose | Shown in the builder | — – — |
| Length прямой посадочной piece | Shown in the builder | 5.0 – 140.0 |
| Конусность по диаметру на посадочной piece | Shown in the builder | -8.0 – 8.0 |
| Add удерживающие рёбра / барбы | Shown in the builder | 0.0 – 6.0 |
| Height барба | Shown in the builder | 0.2 – 2.5 |
| End2 type | Shown in the builder | — – — |
| End2 diameter | Shown in the builder | 10.0 – 250.0 |
| End2 fit | Shown in the builder | — – — |
| End2 length | Shown in the builder | 5.0 – 140.0 |
| End2 taper | Shown in the builder | -8.0 – 8.0 |
| End2 barbs | Shown in the builder | 0.0 – 6.0 |
| End2 barb height | Shown in the builder | 0.2 – 2.5 |
| Mold перехода между диаметрами | Shown in the builder | — – — |
| Transition length | Shown in the builder | 5.0 – 180.0 |
| Wall thickness | Shown in the builder | 1.0 – 10.0 |
| Посадочный gap по диаметру | Shown in the builder | 0.0 – 3.0 |
| Эксцентриситет второго конца по X | Shown in the builder | -40.0 – 40.0 |
| Эксцентриситет второго конца по Y | Shown in the builder | -40.0 – 40.0 |
| End1 stop ring | Shown in the builder | — – — |
| End2 stop ring | Shown in the builder | — – — |
| Stop ring height | Shown in the builder | 0.8 – 10.0 |
| Stop ring overhang | Shown in the builder | 0.5 – 10.0 |
| Flange shape | Shown in the builder | — – — |
| Flange overhang | Shown in the builder | 3.0 – 45.0 |
| Flange thickness | Shown in the builder | 2.0 – 20.0 |
| Четыре монтажных hole на плоском фланце | Shown in the builder | — – — |
| Flat landing hole diameter | Shown in the builder | 2.0 – 12.0 |
| Flat landing hole spacing | Shown in the builder | 15.0 – 180.0 |
| Magnet count | Shown in the builder | 3.0 – 20.0 |
| Magnet diameter | Shown in the builder | 3.0 – 25.0 |
| Magnet depth | Shown in the builder | 1.0 – 10.0 |
| Magnet border | Shown in the builder | 2.0 – 15.0 |
| Дополнительный gap кармана магнита | Shown in the builder | 0.0 – 1.0 |
| Alignment lip | Shown in the builder | — – — |
| Alignment lip width | Shown in the builder | 0.5 – 6.0 |
| Alignment lip height | Shown in the builder | 0.3 – 5.0 |
| Alignment clearance | Shown in the builder | 0.0 – 1.0 |
| Seal groove | Shown in the builder | — – — |
| Seal groove width | Shown in the builder | 1.0 – 6.0 |
| Seal groove depth | Shown in the builder | 0.4 – 3.0 |