шестерня
A parametric model configurable in the ABGUL builder.
Configure the model
Review the parameters, then open the model in the builder. Change dimensions methodically and inspect the result before manufacturing.
Open in builderOutput and formats
The builder displays a 3D preview. Available export formats, design saving and ordering depend on the model and account permissions and are shown in the interface.
Parameters
| Parameter | Units | Range |
|---|---|---|
| Dimension by X - width | Shown in the builder | — – — |
| Dimension by Y - depth | Shown in the builder | — – — |
| Dimension by Z - height | Shown in the builder | — – — |
| Select the gear type to display. | Shown in the builder | — – — |
| Define gear size using circular pitch or module. | Shown in the builder | — – — |
| Set circular pitch or module, based on Mode. | Shown in the builder | 0.3 – 10.0 |
| Number of teeth on the gear. | Shown in the builder | 6.0 – 160.0 |
| Thickness of the gear body. | Shown in the builder | 1.0 – 40.0 |
| Зазор at the lower of the inter-tooth valleys. | Shown in the builder | 0.0 – 3.0 |
| Зазор between two meshing teeth. | Shown in the builder | 0.0 – 3.0 |
| Pressure angle for tooth profile. | Shown in the builder | 14.5 – 35.0 |
| Helical angle of the teeth. | Shown in the builder | -45.0 – 45.0 |
| Enables herringbone teeth when a helical angle is set. | Shown in the builder | — – — |
| Select the center bore shape. | Shown in the builder | — – — |
| Основное bore diameter. | Shown in the builder | 0.5 – 60.0 |
| Depth of each flat for D-shaped bores. | Shown in the builder | 0.0 – 20.0 |
| Side length for square bore. | Shown in the builder | 0.5 – 60.0 |
| Across-corners diameter for hex bore. | Shown in the builder | 0.5 – 60.0 |
| Width of keyway. | Shown in the builder | 0.2 – 20.0 |
| Depth of keyway. | Shown in the builder | 0.2 – 10.0 |
| Rotation of non-round bore. | Shown in the builder | 0.0 – 360.0 |
| Pressure angle of internal teeth. | Shown in the builder | 14.5 – 35.0 |
| Radial wall outside the internal tooth tips. | Shown in the builder | 0.5 – 40.0 |
| Helical angle of internal teeth. | Shown in the builder | -45.0 – 45.0 |
| Enables herringbone internal teeth. | Shown in the builder | — – — |
| Pressure angle used to taper crown teeth. | Shown in the builder | 14.5 – 35.0 |
| Solid backing thickness below crown teeth. | Shown in the builder | 0.5 – 30.0 |
| Radial width of the toothed face. | Shown in the builder | 1.0 – 30.0 |
| Height of crown teeth. | Shown in the builder | 0.5 – 15.0 |
| Center bore diameter. | Shown in the builder | 0.0 – 60.0 |
| Number of teeth on the mating bevel gear. | Shown in the builder | 6.0 – 160.0 |
| Угол between the two shafts. | Shown in the builder | 20.0 – 160.0 |
| Pressure angle. | Shown in the builder | 14.5 – 35.0 |
| Width of the bevel tooth face. | Shown in the builder | 1.0 – 30.0 |
| Solid backing below the tapered gear. | Shown in the builder | 0.0 – 20.0 |
| Spiral angle. Zero gives straight bevel teeth. | Shown in the builder | -45.0 – 45.0 |
| Reverse spiral direction. | Shown in the builder | — – — |
| Center bore diameter. | Shown in the builder | 0.0 – 60.0 |
| Choose a worm or its mating wheel. | Shown in the builder | — – — |
| Pitch diameter of the worm. | Shown in the builder | 4.0 – 100.0 |
| Length of the worm. | Shown in the builder | 5.0 – 160.0 |
| Number of thread starts. | Shown in the builder | 1.0 – 8.0 |
| Pressure angle for thread/tooth shape. | Shown in the builder | 14.5 – 35.0 |
| Left-handed thread. | Shown in the builder | — – — |
| Bore diameter through worm or wheel. | Shown in the builder | 0.0 – 60.0 |
| Wheel thickness when Worm Wheel is selected. | Shown in the builder | 2.0 – 40.0 |
| Number of teeth on the rack. | Shown in the builder | 2.0 – 100.0 |
| Pressure angle of rack teeth. | Shown in the builder | 14.5 – 35.0 |
| Height of solid material below tooth roots. | Shown in the builder | 0.5 – 30.0 |
| Helical angle through the rack thickness. | Shown in the builder | -45.0 – 45.0 |
| Enables herringbone rack. | Shown in the builder | — – — |
| Circular resolution. | Shown in the builder | 24.0 – 180.0 |
| Samples on each involute tooth flank. | Shown in the builder | 4.0 – 24.0 |
| Samples along each tooth tip. | Shown in the builder | 2.0 – 12.0 |
| M | Shown in the builder | — – — |
| Fn | Shown in the builder | — – — |